Double sheet sensor UDC-30GS-3EP1-IO-0,2M-V19

General specifications

Sensing range

50 ... 150 mm , optimal distance: 80 mm

Transducer frequency

approx. 85 kHz

Memory

Non-volatile memory

EEPROM

Write cycles

300000

Indicators/operating means

LED green

indication: single sheet detected
flashing (1 Hz) - standby mode
flashing with short break (1 Hz) - IO-Link mode

LED yellow

indication: no sheet detected (Air)

LED red

indication: double sheet detected
flashing: device error

Electrical specifications

Operating voltage

18 ... 30 V DC , ripple 10 %SS

No-load supply current

≤ 100 mA

Power consumption

≤ 1500 mW

Time delay before availability

≤ 300 ms

Interface

Interface type

IO-Link

IO-Link revision

1.1

Device profile

Identification and Diagnosis - I&D

Process data

Input: 16 Bit
- measurement value 8 Bit
- selected threshold set 2 Bit
- switching signals 3 Bit
Output: 8 Bit
- threshold set 2 Bit
- disable transducer 1 Bit

Vendor ID

1 (0x0001)

Device ID

3148291 (0x300A03)

Transfer rate

COM1 (4.8 kbits/s)

Min. cycle time

22.4 ms

SIO mode support

yes

Compatible master port type

Class A (use adapter cable listed in accesories)
Class B (use 3-pole adapter or 3-wire cable)

Input/Output 1

Designation

SYNC

Input/output type

1 synchronization connection, bidirectional

0 Level

0 ... 1 V

1 Level

2.5 V ... U_B

Input impedance

> 22 kΩ

Output rated operating current

current source < 2.5 mA

Pulse length

0.4 ... 6 ms with external control, low active

Synchronization frequency

Common mode operation

≤ 140 Hz

Multiplex operation

≤ 140 Hz /n, n = number of sensors , n ≤ 10

Input/Output 2

Designation

IN2/FEEDBACK

Input/output type

input or output programmable via IO-Link :
input for selection of a threshold set (factory default)
output as feedback output

Input type

digital input

Signal

0-level: 0 ... + 1V
1-level: +U_B - 1 V ... +U_B

Input impedance

≥ 60 kΩ

Pulse length

≥ 100 ms

Output type

PNP

Rated operating current

8 mA

Voltage drop

< 3 V

Fusing

reverse polarity protected , overload and short-circuit protected

Input

Designation

IN1/TEACH

Input type

0-level: 0 ... + 1V
1-level: +U_B - 1 V ... +U_B

Pulse length

≥ 100 ms

Impedance

≥ 60 kΩ

Output

Designation

OUT 1 ... 3

Number

3

Output function

OUT 1: single sheet detected
OUT 2: double sheet detected
OUT 3: no sheet detected (air)

Output type

Push-pull (4 in 1) output , NC contact ( programmable )

Rated operating current

100 mA per output

Voltage drop

≤ 3 V

Switch-on delay

30 ms (programmable)

Switch-off delay

30 ms (programmable)

Pulse extension

can be activated (100 ms or IO-Link cycle time)

Fusing

reverse polarity protected , overload and short-circuit resistant

Compliance with standards and directives

Standard conformity

Standards

EN IEC 60947-5-2:2020
IEC 60947-5-2:2019
IEC 61131-9 / IO-Link V1.1.3

Approvals and certificates

UL approval

cULus Listed, General Purpose, Class 2 Power Source

CCC approval

CCC approval / marking not required for products rated ≤36 V

Ambient conditions

Ambient temperature

0 ... 60 °C (32 ... 140 °F)

Storage temperature

-25 ... 70 °C (-13 ... 158 °F)

Mechanical specifications

Connection type

fixed cable with plug

Housing length

Ultrasonic transmitter

56 mm

Ultrasonic receiver

78 mm

Housing diameter

Ultrasonic transmitter

30 mm

Ultrasonic receiver

30 mm

Degree of protection

IP65

Material

Housing

Stainless steel 1.4305/AISI 303, polyamide plastic parts

Transducer

epoxy resin/hollow glass sphere mixture; polyurethane foam

Connector

Threading

M12 x 1

Number of pins

8

Cable

Cable diameter

4.3 mm

Bending radius

5 x diameter , fixed

Material

PUR

Color

black

Length

approx. 200 mm

Mass

300 g

Tightening torque, fastening screws

max. 30 Nm